The RTH230B programmable thermostat can be used to control:
•a gas, fuel oil or electric furnace - 2 or 3 wires
•a central air conditioner - 2 or 3 wires
•a hot water system with or without pump - 2 wires
•a millivolt system - 2 wires
•a central heating and cooling system - 4 or 5 wires
Note: These thermostats are not compatible with heat pumps or
multi-stage systems.
Features
•System operating mode selection: heat, cool or off
•Fan operating mode selection: automatic or on (continuous)
•Programmable heating and cooling cycle lengths: 10, 12, 15, 20
or 30 minutes
•Temperature display in °F or °C
•Battery replacement indicator
•5-2 programming including:
- Preprogrammed energy-saving schedule
- Early Start
- Temporary bypass
- Time display (12 h or 24 h)
•Filter replacement indicator
2.1 Removing the Old Thermostat
IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT
POWER TO THE HEATING SYSTEM.
n Remove the old thermostat to access the wires.
Warning: If the old thermostat was mounted onto an electrical box,
it was probably powered by 120/240 volts. In this case, this thermo-
stat cannot be used.
oIdentify and label each wire (with the corresponding letter on
the wire terminal) and remove them from the terminals.
p If necessary, strip the end of each wire (maximum of 1/4 inch).
q Wrap the wires around a pencil to prevent
them from falling into the wall.
r If the hole in the wall is too big, insulate it
using a non-flammable material in order to
avoid air draughts behind the thermostat.
2.2 Installing the New Baseplate
For a new installation, choose a location approximately 5 feet
(1.5 m) above the floor and on an inside wall. Avoid draughty
areas (top of staircase, air outlet, etc.), dead air spots (behind
doors), direct sunlight or areas near concealed pipes or chim-
neys.
n Remove the thermostat faceplate.
o Loosen the locking screw to separate the thermostat from its
baseplate (the screw cannot be completely removed).
p Tilt the thermostat upwards.
q Mark and bore the appropriate mounting holes (or use the
existing holes). Insert the plastic anchors.
r Pass the wires through the opening of the baseplate and fix the
baseplate to the wall using the screws provided.
2.3 Connecting the Thermostat
The connection of the new thermostat should be similar to that of
the old thermostat; however, it can vary depending on the installa-
tion.
Note: The red jumper wire between the Rc and Rh terminals must
be removed in 2- or 5-wire installations. The jumper must be used in
3- or 4-wire installations if you wish to use the mode selector switch
for the fan.
1. Introduction
2. Installation
RTH230B
Programmable Electronic Thermostat
Installation and User Guide
Display
Adjustment
buttons
System operating
mode selector
Fan operating
mode selector
Programming
buttons
RhHeating power supply
RcCooling power supply
WHeating signal
YCooling signal
GFan
여기에서 Honeywell RTH230B에 대한 매뉴얼을 무료로 보십시오. 이 매뉴얼은 카테고리 온도조절기에 속하며 9.2 평균을 가진 2 사람들의 평가를 받았습니다. 이 매뉴얼은 다음 언어로 제공됩니다: 영어. Honeywell RTH230B에 대해 질문이 있습니까? 아니면 도움이 필요하십니까? 여기에 질문하십시오.
도움이 필요하십니까?
Honeywell 에 대한 질문이 있고 매뉴얼에 답변이 없습니까?
솔루션에 대한 업데이트 받기
질문에 대한 답변 받기
질문과 답변
질문 수: 0
Honeywell RTH230B는 온도 제어 장치입니다. 이 제품은 스마트하고 정확한 온도 관리를 제공합니다. 터치 스크린을 지원하므로 사용자는 편리하게 온도를 조절할 수 있습니다. 이 장치는 최대 2개의 온도 설정으로 사용자 맞춤형 온도를 유지할 수 있습니다. 또한 이 제품은 쉽게 설치할 수 있으며, 사용자가 선택한 시간에 온도를 자동으로 조절할 수 있는 타이머를 포함합니다.
Honeywell RTH230B는 어떤 유형의 난방 시스템에도 호환됩니다. 사용자는 가정용, 상업용, 산업용 환경에서 이 온도 제어 장치를 사용할 수 있습니다. 이 제품은 에너지를 절약하는 다양한 기능을 제공합니다. 예를 들어, 이 장치는 온도 조절을 통해 에너지 절약을 돕는 프로그램을 가지고 있습니다.
Honeywell RTH230B는 경제적이고 실용적인 온도 관리 솔루션입니다. 이 제품은 사용자 개인의 환경에 맞게 조정될 수 있어 가정 및 업무 공간에서 모두 사용하기에 좋습니다. 또한 이 온도 제어 장치는 사용하기에도 쉽고, 에너지를 절약하는 기능을 가지고 있어 사람들이 선호하는 제품 중 하나입니다.
도움이 필요하십니까?
Honeywell 에 대한 질문이 있고 매뉴얼에 답변이 없습니까?
질문과 답변
질문 수: 0