Melitta Cafina XT4 매뉴얼

Melitta Cafina XT4
8.2 · 2
PDF 매뉴얼
 · 1 페이지
영어
매뉴얼Melitta Cafina XT4

Melitta

®

660 DE-2

Dimension and data sheet

Attention: All dimensions are approximate!
All Melitta® machines are delivered ready for connection. However, before setting up the necessary connections must be
installed on site easily accessible within a radius of 1 m.
This preliminary work must be performed by licensed professionals in strict compliance with valid regulations. The Melit-
ta® customer service is not authorised for this work and therefore does not take any responsibility for the installation.
The sanitary and electrical connections are located on the back of the machine. The machine must be placed on a solid
tabletop.
If the supply lines are routed up from below the table, an * approx. Ø 100 mm must be drilled behind/under the machine.
a + a1) Electrical connection
400 V 3 N ~ , Power consuption see table.
The supply line must be separately fused by the customer. The connection must be made via an easily accessible
earthing contact socket outlet or CEE socket. The socket must be protected by a ground fault circuit breaker (max. 30
mA). If permanent connection cannot be avoided, a switch with min. 3 mm contact separation must be installed in the
immediate vicinity of the machine for the purpose of all-pole isolation.
b + b1) Water supply
DN 15 - G 3/4“ male thread
According to the regulations of the German Association for Gas and Water (DVGW) a water tap with check valve must
be installed in an easily accessible place by the customer. A special connection hose is supplied. For safety reasons, this
hose should not be shorted. The static water line pressure must be at least 0.2 MPa (2 bar). If the pressure is higher than
0.6 MPa a pressure reducer must be installed by the customer upstream of the stop cock (6 bar).
c) Waste water connection
NW 25 - 1“
The above machine is tted with a water drainage socket and is to be connected to an on-site drain using the supplied
hose. An odour trap should be installed.
Dimensions A B C D Power
consuption
(kw) / Fuse
(A)
Total
weight,
lled (kg)
Type
6610 DE-2 787 702 847 597 (2x) 6,43/16 81,0
6610 W DE-2 787 702 847 597 (2x) 8,50/20 97,0
6620 DE-2 890 805 950 700 (2x) 9,38/16 119,0
6620 W DE-2 890 805 950 700 (2x) 11,45/25 135,0
Date:
Page:
Subject to alterations.
Ownership of Melitta.
Duplication not allowed.
10/2014
1/1
6610 DE-2 is shown
392
531
30
190
D
C
a.
min. 650
min. 600
c.
a1.
b.b1.
1. 3.
2.
392
292
50
350
c.
b. a
.
b1.a1.
50
200 292 200
c.
684
1368
70
* Opening 100 mm
a./b.
a1./b1.
1368
4
1. Flow heater DE
2. Pyramid lter SF
3. Warming unit WA
4. Drip bar

여기에서 Melitta Cafina XT4에 대한 매뉴얼을 무료로 보십시오. 이 매뉴얼은 카테고리 커피 메이커에 속하며 8.2 평균을 가진 2 사람들의 평가를 받았습니다. 이 매뉴얼은 다음 언어로 제공됩니다: 영어. Melitta Cafina XT4에 대해 질문이 있습니까? 아니면 도움이 필요하십니까? 여기에 질문하십시오.

도움이 필요하십니까?

Melitta 에 대한 질문이 있고 매뉴얼에 답변이 없습니까?

  • 솔루션에 대한 업데이트 받기
  • 질문에 대한 답변 받기

질문과 답변

질문 수: 0

일반사항
브랜드Melitta
모델Cafina XT4
제품커피 메이커
언어영어
파일 형식사용자 매뉴얼 (PDF), 데이터 시트 (PDF)

설명서에서 질문에 대한 답을 찾을 수 없습니까? 아래 Melitta Cafina XT4에 대해서 FAQ에서 질문에 대한 답변을 찾을 수 있습니다.

커피 메이커 석회질을 얼마나 자주 제거해야 합니까?

커피 머신의 석회질 제거 빈도는 사용 빈도와 물의 경도에 따라 다릅니다. 경수를 사용하는 경우 한 달에 한 번 석회질을 제거하고, 연수를 사용하는 경우 분기에 한 번이면 충분합니다.

커피 메이커의 석회질을 제거하는 가장 좋은 방법은 무엇입니까?

커피 메이커의 석회질을 제거하려면 커피 머신에 적합하다고 표시된 액체 석회질 제거제를 사용하는 것이 좋습니다.

에스프레소란?

에스프레소는 소량의 농축 커피입니다.

원두커피는 얼마나 오래 보관할 수 있나요?

유통기한은 커피 원두 포장에서 확인할 수 있습니다. 이 유통기한은 커피포장팩이 닫혀 있는 동안 적용됩니다.

커피를 보관하는 가장 좋은 방법은 무엇입니까?

밀폐되고 깨끗한 용기에 커피를 보관하는 것이 좋습니다.

그라인딩은 커피의 맛에 대해 무엇을 말합니까?

커피 원두를 분쇄하는 방법은 커피의 맛에 큰 영향을 미칩니다. 커피 원두를 아주 곱게 갈면 맛이 더 강해지고 굵게 갈면 부드러운 맛이 납니다.

Melitta Cafina XT4의 매뉴얼은 한국인에서 사용할 수 있습니까?

죄송합니다. 한국인에서 사용할 수 있는 Melitta Cafina XT4에 대한 매뉴얼이 없습니다. 이 매뉴얼은 영어에서 사용할 수 있습니다.

귀하의 질문이 목록에 없습니까? 여기에 질문하십시오.

결과 없음