1 2 3Check that you have all the accessories, then put the batteries in the remote control.Video cableFM antennaAM loop antenna
Connect the AM and FM antennas to the rear panel of the DVD/CD receiver.Only use the included AM loop antenna.
Push open the tabs, then insert one wire fully into each terminal.Release the tabs to secure the AM antenna wires.Pull off the protective shields of both AM antenna wires.
Fix the AM loop antenna to the attached stand.To fix the stand to the antenna, bend in the direction indicated by the arrow (fig. A) then clip the loop onto the stand (fig. B).Note: If you plan to mount the AM antenna to a wall or other surface, secure the stand with screws (fig. C) before clipping the loop to the stand. Make sure the reception is clear.
Place the AM antenna on a flat surface and point in the direction giving the best reception. Don’t let it come into contact with metal objects and avoid placing near computers, television sets or other electrical appliances.Connect the FM wire antenna to the FM UNBAL 75 Ω antenna terminal.For best results, extend the FM antenna fully and fix to a wall or door frame. Don’t drape loosely or leave coiled up.
When connecting this system or changing connections, be sure to switch the power off with the STANDBY/ON button, and disconnect the power cord from the AC outlet.
Do not use these speakers with any other system or amplifier as this may result in damage or fire.
Connect each speaker using the color-coded speaker plugs. Match them to the colored speaker terminals on the rear panel of the DVD/CD receiver.For the best surround sound, setup your speakers as above. The front left and right speakers should be about 1.8 m to 2.7 m apart.Congratulations! You're done setting up.
These speaker terminals carry HAZARDOUS LIVE voltage. To prevent the risk of
electric shock when connecting or disconnecting the speaker cables, disconnect the power cord before touching any uninsulated parts.
Connect the DVD/CD receiver to your TV, then connect the
supplied power cord.
Connect the power cord to the AC inlet.
Connect one end to a video input on your TV.
Use the supplied video cord.
Using the remote control
The remote control can be used within a range of about 7 meters
from the remote sensor on the front panel, and within a 30 degree
• The remote control may not work if there is an obstacle
between the remote control and the display unit, or if the remote
control is not directed towards the remote sensor of the display
unit at the correct angle.
• The remote control may not work properly if strong light such
as direct sunlight or fluorescent light is shining onto the unit’s
• The remote control may not work properly when this unit is
used near devices emitting infrared rays, or when remote controls
of other devices which use infrared rays are used. Also, the use of
this remote control may cause other devices to work improperly.
• When the operating range of the remote becomes too short,
replace the batteries.
Remote control battery caution
Incorrect use of batteries may cause leakage or rupture.
Always be sure to follow these guidelines:
• Always insert batteries into the battery compartment correctly
matching the positive ª and negative · polarities, as shown by
the display inside the compartment.
• Never mix new and used batteries.
• Batteries of the same size may have different voltages,
depending on brand. Do not mix different brands of batteries.
• When disposing of used batteries, please comply with
governmental regulations or environmental public instruction's
rules that apply in your country or area.
• In order to prevent battery leakage, remove the batteries when
not using the remote control for an extended period (one month
or more). If leakage occurs, carefully wipe away any battery fluid
inside the compartment, and replace the batteries with new ones.
• Do not allow books or other objects to rest on top of the
remote control, since the buttons may be depressed, causing faster
exhaustion of the batteries.
• Do not use or store batteries in direct sunlight or excessively
hot places, such as inside a car or near a heater. This can cause
batteries to leak, overheat, explode or catch fire. It can also reduce
the life or performance of batteries.
Additional notes on connecting antennas
• Keep antenna cables away from the main unit and other cables.
• To assure optimum reception, pull the FM antenna so that it is fully
extended and not coiled or hanging at the rear of the unit.
• If reception with the supplied antenna is poor, see the Other
connections section in the main operating instructions for details on
connecting outdoor antennas.
Additional notes on speaker placement
If your listening room is of adequate size, place the speakers as
shown in step 3 to achieve the optimum surround sound effect. If
you are listening in a fairly small room and a typical surround speaker
setup is not possible, see Home theater sound setup in the instruction
manual and the Speaker Setup Guide for information on the Front
Surround 3-spot setup option.
When using the standard surround speaker setup as shown in step 3,
please observe the following guidelines:
• Install the main front left and right speakers at an equal distance
from the TV.
For optimum effect, place the surround speakers slightly above ear
• Install the center speaker above or below the TV so that the
sound of the center channel is localized at the TV screen.
• When installing the center speaker on top of the TV, be sure to
secure it with tape or some other suitable means. Otherwise, the
speaker may fall from the TV due to external shocks such as
earthquakes, endangering those nearby or damaging the speaker.
• Do not connect the supplied speakers with any other amplifier.
This may result in malfunction or fire.
• The front, center and surround speakers supplied with this system
are magnetically shielded. However, depending on the installation
location, color distortion may occur if the speaker is installed
extremely close to the screen of a television set. If this happens case,
turn the power switch of the television set OFF, and turn it ON after
15 min to 30 min. If the problem persists, place the speaker system
away from the television set.
• The subwoofer is not
and so should not be
placed near a TV or monitor. Magnetic storage media (such as floppy
discs and tape or video cassettes) should also not be kept close to
• Do not attach the subwoofer to the wall or ceiling. They may fall
off and cause injury.
Connect the other end to the video output of the DVD/CD receiver.
This player is equipped with copy protection technology. Do not connect this player to your TV via a VCR using AV cables, as the picture from this player will not appear properly on your TV. Printed in<XRE3148-A>Connect each speaker as shown below.Match the color-coded speaker plugs to the colored speaker terminals on the rear of the DVD/CD receiver (as shown at left). Make sure to insert completely.The small lug at the wire-end of the speaker plug should face up or down depending on whether it's being plugged into one of the upper or lower three speaker terminals. Please make sure to connect correctly.Upper three terminalsLower three terminalsRemote controlAA/R6 dry cell batteries (to confirmsystem operation)Power cord*Power plug adapter**
** Illustration shows the Central and South
* In some countries or regions, the shape of the
power plug may sometimes differ from that
shown in the explanatory drawings.
Ω - 6 Ω)
Ω - 6 Ω)
UNBAL 75 Ω
UNBAL 75ΩAM LOOP
VIDEO INTo AC outletAC INVIDEO
TOP MENURETURNTEST TONESOUNDCLEARLINE OUT
OPEN/CLOSEINPUT CHANNEL VOLUMEDVD/CDTUNER(FM/AM)VOLUMETV CONTROLFront right (Red)Front left(White)Surround left (Blue)Surround right (Grey)Listening positionCenter (Green)Subwoofer (Purple)This is a standard multichannel surround sound speaker setup for optimal 5.1 channel home theater sound.
Attach the smaller non-skid pads to the base of each of the front speakers and the center speaker. The four large non-skid pads are for the subwoofer (as shown).Use the supplied adhesive to attach 4 pads to the base (flat surface) of each speaker.
Connect the speaker system.Refer to the Setting up your DVD/CD Receiver(the other part of this setup guide) to connect the speakers properly. Place them as shown in the diagram above for optimal surround sound.
Secure the speaker wire.After testing for the slack necessary to turn the speaker (see the following step), use the groove provided to secure the speaker wire.Standard surround5-spot setup• Non-skid pads (large) x 4• Non-skid pads (small) x 12• Mounting brackets x 4This setup is ideal when rear surround speaker placement isn’t possible or you want to avoid running long speaker cables in your listening area.Front surround 3-spot setup
Speaker Setup Guide
Check that you have all the speaker accessories.Front speakersCenter speakerSubwoofer
Connect the speaker system.Refer to the Setting up your DVD/CD Receiver (the other part of this setup guide) to connect the speakers properly. Place them as shown in the diagram above for optimal surround sound.The base of each surround speaker fits into the circular groove on the top of the front speakers as shown.
Attach the smaller non-skid pads to the base of each of the front speakers and the center speaker. The four large non-skid pads are for the subwoofer (as shown).Use the supplied adhesive to attach 4 pads to the base (flat surface) of each speaker.Front speakers Center speakerSubwoofer• Screws(for mounting brackets) x 4 Attaching the brackets
• Make sure to tighten the supplied screw as securely as possible when attaching the bracket to the back of the speaker.
• Please do not attach the brackets to the center speaker. Before mounting
• Remember that the speaker system is heavy and that its weight could cause the wood screws to work loose, or the wall material
to fail to support it, resulting in the speaker falling. Make sure that the wall on which you intend to mount the speakers is strong
enough to support them. Do not mount on plywood or soft surface walls.
• Mounting screws are not supplied. Use screws that are suitable for the wall material and that will support the weight of the
speaker.• If you are unsure of the qualities and strength of the walls, consult a professional for advice.• Pioneer is not responsible for any accidents or damage that result from improper installation.
Switch Front Surround MODE OFF for 5-spot set up.See the operating instructions for more on using Front Surround.Wall-mounting the front and surround speaker system• Front speakers x 2• Center speaker x 1• Surround speakers x 2• Subwoofer x 1Caution
Turn the speakers towards the closest wall, lining the arrows up for optimal Front Surround.
For Front Surround mode, turn each surround speaker so that the arrow at the base is lined up with the (FRONT
SURROUND) arrow on the front speaker. For Extra Power mode, have all the speakers facing forward. See the operating
instructions for more on using Front Surround and Extra Power modes.Extra Power MODE OFF(Front Surround MODE ON)Extra Power MODE ON(Front Surround MODE ON)Caution• To prevent accidents, make sure the surround speaker is placed securely on top of the front speaker.• Please don't the attach speakers to the wall or speaker stands for Front surround 3-spot setup.S-DV161
Pioneer 에 대해 질문이 있고, 그에 대한 답을 설명서에서 찾을 수 없나요? 여기에서 질문하십시오. 문제와 귀하의 질문에 대한 명확하고 포괄적인 설명을 제공하십시오. 귀하의 문제와 질문에 대해서는 다른 Pioneer 소유자가 더 쉽게 좋은 답변을 제공할 수 있습니다.
질문 수: 0